# Content not in center of HyperPixel 2.1 Round

**URL:** <https://forums.pimoroni.com/t/content-not-in-center-of-hyperpixel-2-1-round/18407>\
**Category:** Support\
**Created:** [December 13, 2021, 7:36pm UTC](https://forums.pimoroni.com/t/content-not-in-center-of-hyperpixel-2-1-round/18407 "2021-12-13T19:36:00Z")\
**Posts on this page:** 2\
**Page:** 1

<div class="post-metadata">

**Author:** ![bas](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/bas/32/8382_2.png) [@bas](https://forums.pimoroni.com/u/bas)\
**Post date:** [December 13, 2021, 7:36pm UTC](https://forums.pimoroni.com/t/content-not-in-center-of-hyperpixel-2-1-round/18407/1 "2021-12-13T19:36:00Z")

</div>

Today tried installing a HyperPixel 2.1 Round in combination with a Raspberry Pi Zero 2 W. The Pi is running a fresh install of Buster. I used the default HyperPixel installation using the hyperpixel2r installation script.

The good news; the screen works. The bad news; the whole screen seems to be shifted to the top. As a result the top of the interface (something like 10 pixels?) is missing. On the bottom it results in a bar of repeating lines of pixels (not sure how to explain this easily).

I’ve tried the following things:

- Playing with the overscan settings. \> No effect
- Playing with the frame buffer height and width. \> No effect
- Playing with the dpi\_timings. \> No effect

Is there something else I can try? The pixels are there, and are not broken. The content is just not in the right place.

 ![](https://us1.discourse-cdn.com/flex016/uploads/pimoroni/original/2X/c/c2a6fb7c8b21c1591f662751e5e823971cb513a6.jpeg)

```auto
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=0

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# Force 640x480 video for Pygame / HyperPixel2r
hdmi_force_hotplug=1
hdmi_mode=1
hdmi_group=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2

[all]
#dtoverlay=vc4-fkms-v3d

dtoverlay=hyperpixel2r
enable_dpi_lcd=1
dpi_group=2
dpi_mode=87
dpi_output_format=0x7f216
dpi_timings=480 0 10 16 55 480 0 15 60 15 0 0 0 60 0 19200000 6

```

---

<div class="post-metadata">

**Author:** ![Caperjack1953](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/caperjack1953/32/7923_2.png) [@Caperjack1953](https://forums.pimoroni.com/u/Caperjack1953)\
**Post date:** [December 13, 2021, 11:29pm UTC](https://forums.pimoroni.com/t/content-not-in-center-of-hyperpixel-2-1-round/18407/2 "2021-12-13T23:29:08Z")

</div>

hello, info in this thread was a fix for someone else with same issue ,good luck [Hyperpixel 2.1 Display issues on older RasPis](https://forums.pimoroni.com/t/hyperpixel-2-1-display-issues-on-older-raspis/18369)