# Hyperpixel in Kali Linux

**URL:** <https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104>\
**Category:** Support\
**Created:** [February 6, 2018, 5:23pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104 "2018-02-06T17:23:22Z")\
**Posts on this page:** 13\
**Page:** 1

<div class="post-metadata">

**Author:** ![nexnex](https://avatars.discourse-cdn.com/v4/letter/n/d9b06d/32.png) [@nexnex](https://forums.pimoroni.com/u/nexnex)\
**Post date:** [February 6, 2018, 5:23pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/1 "2018-02-06T17:23:22Z")

</div>

I tried to install my new hyperpixel panel on my raspberry 3 running kali linux today.  
I used: curl [https://get.pimoroni.com/hyperpixel](https://get.pimoroni.com/hyperpixel) | bash  
got a error that i cannot have root access so i made a second account without superuser rights and tried again.  
This time i got this error:

% Total % Received % Xferd Average Speed Time Time Time Current  
Dload Upload Total Spent Left Speed  
100 38282 100 38282 0 0 7547 0 0:00:05 0:00:05 --:–:-- 8391

This script will install everything needed to use  
HyperPixel

Always be careful when running scripts and commands copied  
from the internet. Ensure they are from a trusted source.

If you want to see what this script does before running it,  
you should run: ‘curl [https://get.pimoroni.com/hyperpixel](https://get.pimoroni.com/hyperpixel)’

Your operating system is not supported, sorry!

---

<div class="post-metadata">

**Author:** ![alphanumeric](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/alphanumeric/32/2729_2.png) [@alphanumeric](https://forums.pimoroni.com/u/alphanumeric)\
**Post date:** [February 6, 2018, 8:11pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/2 "2018-02-06T20:11:36Z")

</div>

As far as I know that installer is written for Raspbian. Thus the “your OS is not supported” message.

---

<div class="post-metadata">

**Author:** ![nexnex](https://avatars.discourse-cdn.com/v4/letter/n/d9b06d/32.png) [@nexnex](https://forums.pimoroni.com/u/nexnex)\
**Post date:** [February 6, 2018, 8:50pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/3 "2018-02-06T20:50:08Z")

</div>

I just tried it in raspberian. There the install ran thru without errors. In the end it asked for a reboot typed y and i just got a black screen.

I had a monitor connected via hdmi to the pi at the same time so i disconnected it but it does not help. Also i tried to disconnect the screen and connect the hdmi again to the big monitor but i did not get a picture back.

I hit shift during boot to get into recovery and deleted the hyperpixel entrys from the config. Now i can see again but how do i get this to work?

Also is it normal that the backlight is constantly on before any drivers are installed?

---

<div class="post-metadata">

**Author:** ![alphanumeric](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/alphanumeric/32/2729_2.png) [@alphanumeric](https://forums.pimoroni.com/u/alphanumeric)\
**Post date:** [February 7, 2018, 10:14am UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/4 "2018-02-07T10:14:42Z")

</div>

I don’t personally own one, not yet anyway. I just know that Pimoroni’s installers are written for Raspbian. Just curious, did you use Jessie or Stretch? Did you have anything else connected to the GPIO?

---

<div class="post-metadata">

**Author:** ![gadgetoid](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/gadgetoid/32/13_2.png) [@gadgetoid](https://forums.pimoroni.com/u/gadgetoid)\
**Post date:** [February 7, 2018, 12:41pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/5 "2018-02-07T12:41:33Z")

</div>

> [@nexnex](#):
>
> Also is it normal that the backlight is constantly on before any drivers are installed?

Yes, the backlight has a pull-resistor on its control line so that it’s on by default.

Which version of Raspbian were you using? And which version of the Raspberry Pi?

---

<div class="post-metadata">

**Author:** ![nexnex](https://avatars.discourse-cdn.com/v4/letter/n/d9b06d/32.png) [@nexnex](https://forums.pimoroni.com/u/nexnex)\
**Post date:** [February 7, 2018, 3:50pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/6 "2018-02-07T15:50:16Z")

</div>

My raspberry is a model 3 B.  
First i had raspberian installed under noobs,  
today i tried a clean install of raspberian from a image without noobs, i downloaded the image from the raspberian website (2017-11-29-raspbian-stretch.img) first i used sudo apt-get update, sudo apt-get upgrade and sudo apt-get dist-upgrade until nothing new came in. (Reboots in between) So i used the most recent version of raspberian.

Then i used the command: curl [https://get.pimoroni.com/hyperpixel](https://get.pimoroni.com/hyperpixel) | bash  
No errors came, i pressed y for reboot.

The display behaves the same as before with raspberian under noobs installed (no picture, backlicht on) the only difference is  
without noobs installed i cannot even delete the hyperpixel entrys from my config to see anything again (with shift pressed in on boot nothing happens). But i can use my windows pc to edit the config on the sd card.

In case it matters here is the content of my config:

# For more options and information see

# [http://rpf.io/configtxt](http://rpf.io/configtxt)

# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default “safe” mode

#hdmi\_safe=1

# uncomment this if your display has a black border of unused pixels visible

# and your display can output without overscan

#disable\_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console

# goes off screen, and negative if there is too much border

#overscan\_left=16  
#overscan\_right=16  
#overscan\_top=16  
#overscan\_bottom=16

# uncomment to force a console size. By default it will be display’s size minus

# overscan.

#framebuffer\_width=1280  
#framebuffer\_height=720

# uncomment if hdmi display is not detected and composite is being output

#hdmi\_force\_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)

#hdmi\_group=1  
#hdmi\_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in

# DMT (computer monitor) modes

#hdmi\_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or

# no display

#config\_hdmi\_boost=4

# uncomment for composite PAL

#sdtv\_mode=2

#uncomment to overclock the arm. 700 MHz is the default.  
#arm\_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c\_arm=on  
#dtparam=i2s=on  
#dtparam=spi=on

# Uncomment this to enable the lirc-rpi module

#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd\_bcm2835)

dtparam=audio=on

# HyperPixel LCD Settings

dtoverlay=hyperpixel  
overscan\_left=0  
overscan\_right=0  
overscan\_top=0  
overscan\_bottom=0  
framebuffer\_width=800  
framebuffer\_height=480  
enable\_dpi\_lcd=1  
display\_default\_lcd=1  
dpi\_group=2  
dpi\_mode=87  
dpi\_output\_format=0x6f016  
display\_rotate=2  
hdmi\_timings=800 0 50 20 50 480 1 3 2 3 0 0 0 60 0 32000000 6

# Use a basic GPIO backlight driver with on/off support

dtoverlay=hyperpixel-gpio-backlight

---

<div class="post-metadata">

**Author:** ![alphanumeric](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/alphanumeric/32/2729_2.png) [@alphanumeric](https://forums.pimoroni.com/u/alphanumeric)\
**Post date:** [February 7, 2018, 3:58pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/7 "2018-02-07T15:58:20Z")

</div>

How many Amps is your power supply rated for?

---

<div class="post-metadata">

**Author:** ![nexnex](https://avatars.discourse-cdn.com/v4/letter/n/d9b06d/32.png) [@nexnex](https://forums.pimoroni.com/u/nexnex)\
**Post date:** [February 7, 2018, 4:01pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/8 "2018-02-07T16:01:18Z")

</div>

I have tried my 2.5 Amp power supply which came in the set with the pi (Vilros Adapter), and a 3 amp power supply i had (Rydges SpeedPower)

---

<div class="post-metadata">

**Author:** ![alphanumeric](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/alphanumeric/32/2729_2.png) [@alphanumeric](https://forums.pimoroni.com/u/alphanumeric)\
**Post date:** [February 7, 2018, 4:21pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/9 "2018-02-07T16:21:05Z")

</div>

Ok, just confirming it was a good capacity to rule it out as an issue. The hyperpixel likely draws a fair bit of current.

---

<div class="post-metadata">

**Author:** ![nexnex](https://avatars.discourse-cdn.com/v4/letter/n/d9b06d/32.png) [@nexnex](https://forums.pimoroni.com/u/nexnex)\
**Post date:** [February 7, 2018, 4:23pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/10 "2018-02-07T16:23:40Z")

</div>

I found the error. It was one of the pins, i mesured them all with a meter and one had no connection for whatever reason, visually it looked sound. I replaced it and now it works! Thank you!  
I still hope to get it to work in Kali linux, but i am glad it is not broken.

---

<div class="post-metadata">

**Author:** ![nexnex](https://avatars.discourse-cdn.com/v4/letter/n/d9b06d/32.png) [@nexnex](https://forums.pimoroni.com/u/nexnex)\
**Post date:** [February 7, 2018, 4:36pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/11 "2018-02-07T16:36:45Z")

</div>

It works in Kali Linux!! So happy!\_

---

<div class="post-metadata">

**Author:** ![gadgetoid](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/gadgetoid/32/13_2.png) [@gadgetoid](https://forums.pimoroni.com/u/gadgetoid)\
**Post date:** [February 7, 2018, 4:38pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/12 "2018-02-07T16:38:08Z")

</div>

> [@nexnex](#):
>
> I found the error. It was one of the pins, i mesured them all with a meter and one had no connection for whatever reason, visually it looked sound. I replaced it and now it works! Thank you!

Waaah!? How did you have it connected to your Pi?

---

<div class="post-metadata">

**Author:** ![nexnex](https://avatars.discourse-cdn.com/v4/letter/n/d9b06d/32.png) [@nexnex](https://forums.pimoroni.com/u/nexnex)\
**Post date:** [February 7, 2018, 4:58pm UTC](https://forums.pimoroni.com/t/hyperpixel-in-kali-linux/7104/13 "2018-02-07T16:58:23Z")

</div>

Just those Pins that are used, do not know the name, seems one was not connected. I cannot really imagine it had no connection, its is metal on metal.
