# Soldered headers to wrong side of Explorer pHat

**URL:** <https://forums.pimoroni.com/t/soldered-headers-to-wrong-side-of-explorer-phat/2925>\
**Category:** Support\
**Created:** [August 27, 2016, 8:18pm UTC](https://forums.pimoroni.com/t/soldered-headers-to-wrong-side-of-explorer-phat/2925 "2016-08-27T20:18:14Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![cinnabar](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/cinnabar/32/859_2.png) [@cinnabar](https://forums.pimoroni.com/u/cinnabar)\
**Post date:** [August 27, 2016, 8:18pm UTC](https://forums.pimoroni.com/t/soldered-headers-to-wrong-side-of-explorer-phat/2925/1 "2016-08-27T20:18:14Z")

</div>

I have managed to solder the headers to the wrong side of my Explorer pHat (inexperienced!) - I’m assuming therefore that it’s unusable as the holes in the header (technical term?) will not match up to the correct pins on the Pi Zero.  
I don’t mind just buying a new one, but wondered if there were any other options - desoldering it seems like it might be fiddly, since the soldering iron I was using was a cheap one and the soldering not brilliant. I also don’t have a desoldering pump and would rather spend the money I might spend on that on a better soldering iron.  
Is there anything I can use to connect the correct pins from the Zero to the right holes on the Explorer? I have seen some 40-pin jumper cable strips - would something like this work?

Any advice would be much appreciated…

---

<div class="post-metadata">

**Author:** ![major\_tomm](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/major_tomm/32/9044_2.png) [@major\_tomm](https://forums.pimoroni.com/u/major_tomm)\
**Post date:** [August 27, 2016, 8:39pm UTC](https://forums.pimoroni.com/t/soldered-headers-to-wrong-side-of-explorer-phat/2925/2 "2016-08-27T20:39:53Z")

</div>

Explorer pHAT only uses the [these](http://pinout.xyz/pinout/explorer_phat) pins, so you could just use jumper cables to connect them up to the correct pins?

---

<div class="post-metadata">

**Author:** ![cinnabar](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/cinnabar/32/859_2.png) [@cinnabar](https://forums.pimoroni.com/u/cinnabar)\
**Post date:** [August 27, 2016, 8:42pm UTC](https://forums.pimoroni.com/t/soldered-headers-to-wrong-side-of-explorer-phat/2925/3 "2016-08-27T20:42:46Z")

</div>

Thanks, it hadn’t occurred to me I would need to connect them all.

---

<div class="post-metadata">

**Author:** ![cinnabar](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/cinnabar/32/859_2.png) [@cinnabar](https://forums.pimoroni.com/u/cinnabar)\
**Post date:** [August 27, 2016, 8:43pm UTC](https://forums.pimoroni.com/t/soldered-headers-to-wrong-side-of-explorer-phat/2925/4 "2016-08-27T20:43:32Z")

</div>

I mean wouldn’t need to!

---

<div class="post-metadata">

**Author:** ![karan](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/karan/32/525_2.png) [@karan](https://forums.pimoroni.com/u/karan)\
**Post date:** [August 28, 2016, 1:15pm UTC](https://forums.pimoroni.com/t/soldered-headers-to-wrong-side-of-explorer-phat/2925/5 "2016-08-28T13:15:58Z")

</div>

If you have not soldered the pizero header,then you could solder it up-side down and it would work.

---

<div class="post-metadata">

**Author:** ![archieroques](https://sea2.discourse-cdn.com/flex016/user_avatar/forums.pimoroni.com/archieroques/32/1119_2.png) [@archieroques](https://forums.pimoroni.com/u/archieroques)\
**Post date:** [September 3, 2016, 4:52pm UTC](https://forums.pimoroni.com/t/soldered-headers-to-wrong-side-of-explorer-phat/2925/6 "2016-09-03T16:52:37Z")

</div>

In all honesty, it’s worth spending a bit of money on a decent desoldering pump. It’ll be worth it - even after soldering for years you will inevitably make mistakes, and for what a good one costs it’s a no brainier.
